Dura-Bar,100-70-03 Continuously Cast Ductile Iron Flange ASTM A536

1,We Manufacturing processes are primarily classified into four types: 1:Forging, 2:Casting, 3:Cutting, 4:Rolling. 2,We can manufacture in accordance with these standards. Standards: GB Series (Chinese Standards), JB Series (Machinery Standards), HG Series (Chemical Industry Standards), ASME B16.5 (American Standards), BS4504 (British Standards), DIN (German Standards), and JIS (Japanese Standards). Internationally, there are two primary systems of pipe flange standards: the European system, represented by the German DIN standards (including those of the former Soviet Union), and the American system, represented by the US ANSI pipe flange standards. Other common standards include: the Chinese Ministry of Machinery Industry standards (JB series), the Ministry of Chemical Industry standards (HG series), the Chinese National Standard *GB/T 9112–9124-2010 Steel Pipe Flanges*, as well as US standards (ASME B16.5), British standards (BS4504), German standards (DIN), Japanese standards (JIS), and marine standards (CBM), among others. The nominal pressure ratings for the PN series are designated by "PN" and comprise the following nine levels: PN2.5, PN6, PN10, PN16, PN25, PN40, PN63, PN100, and PN160. The nominal pressure ratings for the Class series are designated by "Class" and comprise the following six levels: Class150, Class300, Class600, Class900, Class1500, and Class2500. Flange Classification 1. **According to Chemical Industry Standards:** Flanges are classified as follows: Plate Flat Welding Flange (PL), Necked Flat Welding Flange (SO), Necked Butt Welding Flange (WN), Integral Flange (IF), Socket Welding Flange (SW), Threaded Flange (Th), Butt Welding Ring Loose Flange (PJ/SE), Blind Flange (BL), Flat Welding Ring Loose Flange (PJ/PJ), and Lined Blind Flange (BL(s)). 2. **According to Petrochemical (SH) Industry Standards:** Flanges are classified as follows: Threaded Flange (PL), Butt Welding Flange (WN), Flat Welding Flange (SO), Socket Welding Flange (SW), Loose Flange (LJ), and Blind Flange (no specific designation). 3. **According to Machinery (JB) Industry Standards:** Flanges are classified as follows: Integral Flange, Butt Welding Flange, Plate Flat Welding Flange, Butt Welding Ring Plate Loose Flange, Flat Welding Ring Plate Loose Flange, Lap Joint Ring Plate Loose Flange, and Blind Flange. 4. **According to Connection Method/Type:** Flanges are classified as follows: Plate Flat Welding Flange, Necked Flat Welding Flange, Necked Butt Welding Flange, Socket Welding Flange, Threaded Flange, Blind Flange, Necked Butt Welding Ring Loose Flange, Flat Welding Ring Loose Flange, Ring-Type Joint (RTJ) Flange and Blind Flange, Large-Diameter Plate Flange, Large-Diameter High-Neck Flange, Figure-8 Blind Plate, Butt Welding Ring Loose Flange, etc. 5. **According to the Component Being Connected:** Flanges can be classified into Vessel Flanges and Pipe Flanges. 6. **According to Structural Type:** Flanges include Integral Flanges, Threaded Flanges, Flat Welding Flanges, Butt Welding Flanges, Lap Joint (Loose/Swivel) Flanges, and Blind Flanges. A flange—also referred to as a flange plate or rim—is a component used to connect shafts to one another, or, more commonly, to join the ends of pipes. Flanges are also utilized at the inlet and outlet ports of equipment to facilitate connections between two devices—for instance, the flange on a speed reducer. A "flange connection" or "flanged joint" refers to a detachable joint assembly comprising three interconnected elements—a flange, a gasket, and bolts—that together form a sealed structural unit. In the context of piping systems, a "pipe flange" specifically denotes a flange used for plumbing within the installation; when applied to equipment, it refers to the inlet or outlet flange of that specific device. Flanges feature a series of holes through which bolts are inserted to securely fasten the two flanges together, while a gasket placed between the flanges ensures a leak-proof seal. Flanges are broadly categorized into three types: threaded (screw-in) flanges, welded flanges, and clamp-type flanges. Flanges are invariably used in pairs; threaded flanges are suitable for low-pressure piping applications, whereas welded flanges are required for systems operating at pressures exceeding 4 kilograms per square centimeter. A sealing gasket is inserted between the two flange plates, which are then firmly secured using bolts. The thickness of a flange—as well as the specifications of the bolts used to fasten it—vary depending on the specific pressure rating required for the application. When connecting equipment such as water pumps or valves to piping systems, the corresponding connection points on these devices are often manufactured in the shape of a matching flange; this method of attachment is also referred to as a "flange connection." Generally, any connecting component that utilizes bolts to join and seal the perimeters of two flat surfaces—such as the joints in ventilation ducts—is termed a "flange"; such components may collectively be classified as "flange-type parts." However, since such a connection often constitutes merely a *portion* of a larger device—for instance, the interface between a flange and a water pump—it would be inappropriate to classify the entire water pump itself as a "flange-type part." Conversely, smaller components—such as valves—that feature such flanged interfaces may indeed be appropriately categorized as "flange-type parts." -:- For detailed product information, please contact sales. -: Dura-Bar 100-70-03 Continuously Cast Ductile Iron Flange Bar Stock ASTM A536 Product Information -:- For detailed product information, please contact sales. -: Dura-Bar 100-70-03 Continuously Cast Ductile Iron Flange Bar Stock ASTM A536 Synonyms -:- For detailed product information, please contact sales. -:

Dura-Bar 100-70-03 Continuously Cast Ductile Iron Bar Stock ASTM A536 Product Information -:- For detailed product information, please contact sales. -: # **Dura-Bar® 100-70-03 Continuously Cast Ductile Iron Bar Stock** ## **Product Overview** **Dura-Bar 100-70-03** is a premium-grade **pearlitic/heat-treated ductile iron** manufactured through an advanced continuous casting process that produces dense, homogeneous, defect-free bar stock. This material conforms to **ASTM A536 Grade 100-70-03** specification, representing the **highest strength class** of standard ductile irons with a unique combination of **exceptional strength, good wear resistance, and retained machinability**. The "100-70-03" designation indicates minimum mechanical properties: **100 ksi (690 MPa) Tensile Strength, 70 ksi (483 MPa) Yield Strength, and 3% Elongation**. Unlike conventional castings, Dura-Bar's continuous casting process eliminates porosity, slag inclusions, and microstructural variations, ensuring predictable performance throughout the entire bar cross-section and length. --- ## **1. International Standards & Specifications** | **Standard System** | **Designation** | **Application/Region** | **Notes** | |---------------------|-----------------|------------------------|-----------| | **ASTM (Primary)** | **A536 Grade 100-70-03** | North America, International | Governs mechanical requirements | | **SAE Automotive** | **J434 D7003** (Approximate) | Automotive industry | Similar performance grade | | **ISO** | **EN-GJS-700-2** (ISO 1083) | European/International | Rough equivalent; properties may vary | | **UNS** | **F34800** (Typical) | Unified Numbering System | For pearlitic ductile irons | | **Manufacturer** | **Dura-Bar 100-70-03** | Global distribution | Proprietary continuous cast process | | **Common Names** | High-Strength Ductile Iron, Heat-Treated Ductile Iron, Continuous Cast Grade 100-70-03 | Industry terminology | | **Note:** While international equivalents exist, Dura-Bar's continuous casting process typically yields **superior and more consistent properties** compared to sand-cast equivalents of the same nominal grade. --- ## **2. Chemical Composition** The chemistry is precisely controlled to achieve a **predominantly pearlitic/martensitic matrix** through alloying and subsequent heat treatment, while maintaining sufficient ductility and machinability. | **Element** | **Typical Range (% Weight)** | **Functional Role** | **Effect on Properties** | |-------------|------------------------------|---------------------|--------------------------| | **Carbon (C)** | 3.3 - 3.6 | Graphite former, matrix strengthener | Lower carbon reduces graphite volume, increases matrix strength | | **Silicon (Si)** | 1.8 - 2.4 | Ferritizer, deoxidizer | Controlled to limit ferrite, enhance hardenability | | **Manganese (Mn)** | 0.5 - 0.8 | Pearlite stabilizer, hardenability agent | Key element for achieving high-strength matrix | | **Phosphorus (P)** | ≤ 0.035 max | Impurity | Minimized to prevent brittle phosphides | | **Sulfur (S)** | ≤ 0.015 max | Impurity | Critical control for successful nodularization | | **Magnesium (Mg)** | 0.04 - 0.06 | **Nodularizing element** | Ensures Type I spheroidal graphite | | **Copper (Cu)** | 0.8 - 1.2 | **Primary alloying element** | Strong pearlite promoter, solid solution strengthener | | **Nickel (Ni)** | 0.5 - 1.0 (Optional) | Austenite stabilizer | Enhances hardenability, toughness in heavy sections | | **Molybdenum (Mo)** | 0.2 - 0.4 | **Hardenability agent** | Refines structure, prevents pearlite transformation | | **Tin (Sn)** | 0.05 - 0.10 | **Powerful pearlite stabilizer** | Ensures consistent high-strength matrix | **Microstructural Characteristics:** - **Graphite:** ASTM Type I, Size 6-7 (small, well-dispersed nodules) - **Matrix:** 90-100% fine pearlite, acicular, or tempered martensite (depending on heat treatment) - **Carbides:** Minimal (<1% typically) - **Unique Feature:** Continuous casting produces finer, more uniform graphite distribution than sand casting --- ## **3. Mechanical Properties** ### **Minimum Requirements (ASTM A536 100-70-03):** - **Tensile Strength:** 100 ksi min (690 MPa) - **Yield Strength (0.2% offset):** 70 ksi min (483 MPa) - **Elongation:** 3% min in 2 inches (50 mm) ### **Typical Achieved Properties (Dura-Bar Continuous Cast):** | **Property** | **Typical Value** | **Range** | **Notes** | |--------------|-------------------|-----------|-----------| | **Tensile Strength** | 105 - 115 ksi (724 - 793 MPa) | Up to 120 ksi possible | 30-40% higher than 80-55-06 grade | | **Yield Strength** | 75 - 85 ksi (517 - 586 MPa) | Consistent across section | Excellent for loaded components | | **Elongation** | 4 - 6% | Typically exceeds minimum | Maintains useful ductility | | **Hardness** | 269 - 302 HB (27 - 32 HRC) | Very consistent | Hardness varies <10% across diameter | | **Modulus of Elasticity** | 24.5 × 10⁶ psi (169 GPa) | Similar to other ductile irons | | | **Fatigue Strength** | 35 - 40 ksi (241 - 276 MPa) endurance limit | Good for cyclic loading | Superior to many steels at same hardness | | **Impact Energy** | 7 - 15 ft-lb (9 - 20 J) Charpy V-notch | Lower than ferritic grades | Adequate for most industrial applications | | **Poisson's Ratio** | 0.27 - 0.28 | Typical for ductile iron | | --- ## **4. Physical Properties** | **Property** | **Value** | **Comparison/Advantage** | |--------------|-----------|--------------------------| | **Density** | 0.260 lb/in³ (7.19 g/cm³) | 10% lighter than steel | | **Thermal Conductivity** | 21.6 Btu/(ft·hr·°F) @ 212°F (37.4 W/m·K) | Excellent heat dissipation | | **Coefficient of Thermal Expansion** | 6.5 × 10⁻⁶/°F (11.7 × 10⁻⁶/°C) 68-212°F | Matches steel for assemblies | | **Specific Heat** | 0.11 Btu/(lb·°F) (460 J/kg·K) | Typical for ferrous alloys | | **Damping Capacity** | 4-6× greater than steel | Excellent vibration absorption | | **Electrical Resistivity** | 45 μΩ·cm | Higher than steel, lower than cast iron | | **Magnetic Properties** | Ferromagnetic | Suitable for electromagnetic applications | --- ## **5. Manufacturing & Processing Characteristics** ### **Machinability:** - **Machinability Rating:** 50-60% (vs. 1212 steel = 100%) - **Cutting Speed:** 300-500 SFPM for turning operations - **Tool Materials:** Recommended C2/C3 carbide or coated inserts - **Chip Formation:** Excellent - produces small, broken chips - **Surface Finish:** 32-63 μin Ra readily achievable - **Advantage:** Despite high hardness, machines 2-3× faster than through-hardened steel of equivalent strength ### **Heat Treatment:** 1. **As-Supplied Condition:** Already heat-treated to achieve specified properties 2. **Stress Relieving:** 900-1100°F (480-595°C) for 1 hour per inch, furnace cool 3. **Surface Hardening:** Flame/induction hardening to 50-55 HRC possible 4. **Nitriding/Carbonitriding:** Effective for extreme wear resistance 5. **Annealing:** Not typically required; would degrade mechanical properties ### **Joining & Fabrication:** - **Welding:** Generally **not recommended** due to high carbon equivalent and alloy content - **Adhesive Bonding:** Excellent with proper surface preparation - **Mechanical Fastening:** Good thread strength (70-80% of tensile strength) - **Plating/Coating:** Accepts most common treatments (chrome, nickel, zinc, etc.) --- ## **6. Application Areas** ### **Primary Industries & Applications:** | **Industry** | **Specific Applications** | **Replacing** | **Advantage** | |--------------|--------------------------|---------------|---------------| | **Hydraulic & Pneumatic** | High-pressure (>3000 psi) pump bodies, valve blocks, manifold plates, cylinder barrels | 4140/4340 steel | Better damping, superior machinability | | **Power Transmission** | Heavy-duty gears, sprockets, coupling hubs, drive shafts, worm gears | Forged steel | Cost-effective, excellent wear resistance | | **Automotive** | Diesel engine components, turbo housings, transmission gears, bearing caps | Steel forgings | Weight reduction, NVH improvement | | **Oil & Gas** | Valve components, compressor parts, wellhead equipment, tool joints | Alloy steels | Corrosion resistance in certain media | | **Industrial Machinery** | Press frames, machine tool components, rolling mill guides, bearing housings | Fabricated steel | Dimensional stability, vibration damping | | **Agricultural** | Combine components, gearbox housings, drive train parts | Cast steel | Better wear resistance, lower cost | ### **Specific Component Examples:** 1. **Gears & Sprockets:** Where high contact stresses are encountered 2. **Hydraulic Manifolds:** For ultra-high-pressure systems (5000+ psi) 3. **Compressor Crankshafts:** Combining strength with damping 4. **Tooling & Fixtures:** Requiring dimensional stability under load 5. **Rolling/Sliding Components:** Bushings, rollers, guides in high-load applications --- ## **7. Comparative Advantages** ### **vs. Competing Materials:** | **Material** | **Relative Cost to Machine** | **Damping Capacity** | **Strength-to-Weight** | **Wear Resistance** | |--------------|------------------------------|----------------------|------------------------|---------------------| | **Dura-Bar 100-70-03** | **1.0 (Baseline)** | **Excellent** | **Very Good** | **Excellent** | | **4140 Steel (Hardened)** | 1.8-2.5× | Poor | Excellent | Very Good | | **4340 Steel** | 2.0-3.0× | Poor | Excellent | Very Good | | **Ductile Iron 80-55-06** | 0.9-1.1× | Excellent | Good | Good | | **Gray Iron** | 0.8-1.0× | Excellent | Poor | Fair | | **Aluminum (T6)** | 0.6-0.8× | Good | Fair | Poor | ### **Key Differentiators:** 1. **Consistency:** Mechanical properties vary <5% within a bar, <8% bar-to-bar 2. **Soundness:** 100% ultrasonically testable, no internal defects 3. **Availability:** Immediate from stock in rounds 0.5"-17" diameter, squares, rectangles 4. **Traceability:** Full metallurgical certification with each shipment --- ## **8. Quality Assurance & Testing** Dura-Bar maintains rigorous quality standards: - **Chemical Analysis:** Spectrographic testing of every melt - **Mechanical Testing:** Tensile tests from each production run - **Microstructural Examination:** Verification of graphite shape and matrix - **Hardness Testing:** Multiple points per bar for consistency - **Non-Destructive Testing:** Ultrasonic testing available for critical applications - **Certification:** Full traceability with heat numbers and test reports --- ## **Technical Summary** **Dura-Bar 100-70-03 Continuous Cast Ductile Iron** represents the **pinnacle of high-strength cast iron technology**, offering: 1. **Exceptional Strength:** Equivalent to heat-treated alloy steels (100+ ksi UTS) 2. **Superior Manufacturability:** Machines 2-3× faster than through-hardened steels 3. **Excellent Damping:** 4-6× better vibration absorption than steel 4. **Consistent Quality:** Predictable properties throughout every bar 5. **Cost Effectiveness:** Lower total finished-part cost vs. steel alternatives This material is ideally suited for **high-stress applications** where traditional ductile irons lack sufficient strength, but where the **machining advantages and damping characteristics** of cast iron are desired. It successfully bridges the gap between conventional ductile irons and high-strength steels, offering a unique combination of properties unavailable in any other single material. --- ## **Engineering Recommendations** ### **When to Specify 100-70-03:** - Tensile requirements exceed 90 ksi (620 MPa) - Wear resistance is critical but machinability must be maintained - Vibration damping is important for performance or noise reduction - Component is complex and would require extensive machining from steel - Thermal conductivity is important for heat dissipation ### **Design Considerations:** - Maintain minimum wall thickness of 0.25" (6 mm) for consistent properties - Avoid sharp corners (use minimum 0.06" radii) - Account for lower elongation than steel in highly stressed areas - Consider stress concentrations in designs requiring >3% elongation ### **Availability:** - **Rounds:** 0.5" to 17" diameter - **Rectangles/Squares:** Up to 16" width - **Lengths:** Standard 12', custom lengths available - **Lead Time:** Most sizes available from stock --- *Note: All values are typical; specific applications should be verified with Dura-Bar technical data sheets and application engineering support.* -:- For detailed product information, please contact sales. -: Dura-Bar 100-70-03 Continuously Cast Ductile Iron Bar Stock ASTM A536 Specification Dimensions Size： Diameter 20-1000 mm Length <6605 mm Size:We can customized as required Standard： Per your request or drawing We can customized as required Properties（Theoretical） Chemical Composition -:- For detailed product information, please contact sales. -: Dura-Bar 100-70-03 Continuously Cast Ductile Iron Bar Stock ASTM A536 Properties -:- For detailed product information, please contact sales. -:

Applications of Dura-Bar 100-70-03 Continuously Cast Ductile Iron Flange Bar Stock ASTM A536 -:- For detailed product information, please contact sales. -: Chemical Identifiers Dura-Bar 100-70-03 Continuously Cast Ductile Iron Flange Bar Stock ASTM A536 -:- For detailed product information, please contact sales. -:

Packing of Dura-Bar 100-70-03 Continuously Cast Ductile Iron Flange Bar Stock ASTM A536 -:- For detailed product information, please contact sales. -: Standard Packing: -:- For detailed product information, please contact sales. -: Typical bulk packaging includes palletized plastic 5 gallon/25 kg. pails, fiber and Steel Flange drums to 1 ton super sacks in full container (FCL) or truck load (T/L) quantities. Research and sample quantities and hygroscopic, oxidizing or other air sensitive materials may be packaged under argon or vacuum. Solutions are packaged in polypropylene, plastic or glass jars up to palletized 3076 gallon liquid totes Special package is available on request. E FORUs’ is carefully handled to minimize damage during storage and transportation and to preserve the quality of our products in their original condition